Alphacool NexXxos ST30 Full Copper Radiator, 360mm, Triple Fan, Black

I have three of these full length babies in my Thermaltake CORE WP100 Extreme Water Cooling XL-ATX Fully Modular Full Tower Computer Case. Alphacool Rocks !!! These are the 30mm thick Radiators and with my fans set up to suck the air through the radiators (No push/pull) there is plenty of room for everybody in the CORE P100 case. I will admit the Plumbing is/was a challenge. But the one thing that impressed me was when I flushed out these radiators for three days each, I found NO gunk in my filter. Just because I didn't find anything does not mean you can skip that step, you have to flush your radiators just in case. You don't want anything killing your pump or blocking the tiny fins in a water block. I am just really impressed there was nothing green in my watts filters. As for attaching them to the fans and the radiator bracket- the screw heads are really small and will slip out of the Thermaltake's radiator's bracket. This is not the fault of Alphacool. Simple fix is to go out and buy some thin metric washers to go behind the screwhead and and in front of the bracket. I had to ask a fellow Core WP100 case owner to find this out. And make sure you have a 2.5mm Allen wrench. It does not come with the screws or the radiator. Also, make sure you use the correct length of screws that comes with the Radiator. Alphacool has done it's best so you don't puncture the radiator with a tab stop for the screws, but you can force it and wreck your radiator. So take your time putting things together. It's a great Radiator.

Just make sure to clean and flush properly to rid of little debris inside, no issues, no leaks.

The radiator is, in fact, full copper and it is relatively well-made. However, the packaging needs some improvement because I had a noticeable 2 inch dent in the fins. This is not a big deal since I can just use some tweezers to bend them back, but still it could have been avoided with a full styrofoam pad along the fins instead of the thin bubble wrap it comes in. Also, even though it's not a real issue, there is a typo on your packaging. "radiator with an thickness of..." should be "radiator with a thickness of..."

I've been exclusive to Alphacool radiators since 2014. I won't use any other brand, and I've used everything from their 80mm thick Monsta series (some of my personal favorites) to their HPM and crossflow series, to these. The 4 stars isn't performance based, as these perform the way one would expect Alphacool radiators to perform, superiorly to any non Alphacool radiator, and at a 5 star rating. The 4 stars is because these left the factory without proper tooling of the mounting tabs. The mounting tabs would not accept the M3 screws, at all. I actually had to use my tap and die set in order to tap these out for the provided M3 screws, which should not be necessary. Albeit the first time in 12 years I've ever experienced this from Alphacool, it isn't an excuse amd shouldn't be tolerated, you guys are better than this. Performance wise, they're everything I'd expect from Alphacool, which is nothing short of the best. I built two of these into one of the smallest builds I've done, basically for use as a firewall for my network, and I'm very impressed by their 30mm thick rads.

Finish looks great and they come with nice screws for mounting. Too bad they didnt have a second set of 30mm for those people using push pull config such as myself. Work great and temps have been sitting low and silent. I have two of these in my system and couldn't be happier with the performance.

I have 2 of these in my computer one the single fan size and the other a double fan size. It helps keep cool 5°C per fan with radiator. They seem to to constructed well and have no problems with leaks. I love this brand for my first water Cooling build and I will use them again if I ever do another.

They're the best. If you want the best in watercooling, Alphacool is it. Once their waterblock arrives.... (looking at you Alphacool) I'll post a photo of it all hooked up. I ran the 3900x on it for a while. It did fine, and ran the same as the 160mm on the back, so I changed it back. Update. I painted them white. Copper logos.

I would install this in my daily driver CAR! It is a single row but it will handily dissipate over 500 watts on slow fans. High pressure fans would easily go farther. I built this a redundant so if one fan failed it still retained cooling capacity of 350 watts.

A little bit of debris came out when flushed rad but overall pretty good. Very tall and long rad. Been leak free and working good. No issues so far

Couplé à une gtx 1080 Ti ça fonctionne très bien,très solide et surtout niveau refroidissement c'est parfait

Beautiful little cooling Radiator, does everything you'd expect it to do, and large enough for my Corsair 750D, takes the entire top half of the case and ends just before the Drive bays. Takes three 120mm fans to cool down and works very well with alpha cool compresion fittings. Defintely recommend this.

Der Artikel kam gut verpackt und völlig unbeschädigt an. Keine verbogenen Kühl-Lamellen oder ähnliches. Die Qualitätsanmutung ist sehr gut. Schrauben zur Befestigung von Lüftern und zum Anschrauben des Radiators liegen bei. Die 1/4 Zoll Anschlüsse für die Schläuche oder Rohre muss man separat kaufen und das ist auch logisch. Alphacool kann ja nicht wissen, welchen Durchmesser oder welche Machart die Leitungen haben sollen. Auch innen war der Radiator sehr sauber. Ich habe ihn natürlich vor Gebrauch durchgespült und das Spülwasser war kaum verunreinigt. Ich habe 2 Lüfter mit je 140mm von beQuiet drauf. Damit ist die Kühlleistung locker ausreichend bis mindestens 120 Watt TDP. Ich würde wegen der leiseren 140er Lüfter immer eher einen 280er Radiator nehmen, als einen der so populären 360er (mit 3 120er Lüftern)..

Funzt wie angedacht o/